TU-A6.2A: 3D Printed Antennas and Structures I
Tue, 15 Jul, 08:00 - 11:40
Location: Rogers Centre: Room 215
Session Type: Oral
Session Co-Chairs: Gary Brown, Virginia Tech and Loïc Markley, University of British Columbia
Track: AP-S: Antenna Applications and Emerging Technologies
Tue, 15 Jul, 08:20 - 08:40

TU-A6.2A.2: 3-D Printable Crossover-Free WR12 Butler Matrix for a 1x4 Beamforming Antenna Array
Jean Temga, Silicon Austria Labs, Austria; Peter Bauer, TIGER Coatings GmbH & Co. KG, Austria; Michael J. Haslinger, PROFACTOR GmbH, Austria; Saeid Karamzadeh, Silicon Austria Labs, Austria
Tue, 15 Jul, 08:40 - 09:00

TU-A6.2A.3: A 3D-Printed Microwave Absorber Using Carbon Nanotube/Polymer Nanocomposites
Ailar Sedghara, Loïc Markley, Mohammad Arjmand, University of British Columbia, Canada
Tue, 15 Jul, 09:00 - 09:20

TU-A6.2A.4: 3D-Printed Lens Antenna With Wide-Band Feed for mm-wave Applications
Zunnurain Ahmad, Infineon Technologies, Germany; Lee Harle, Michian State University, United States; Aljoscha Roch, Fraunhofer USA, United States
Tue, 15 Jul, 09:20 - 09:40

TU-A6.2A.5: An Integrated Planar Luneburg Lens Antenna With Improved Impedance Matching
Hojjat Jamshidi Zarmehri, Jafar Shaker, Department of Electronics, Carleton University, Ottawa, Canada; Eqab Almajali, Engineering Department, University of Sharjah, Canada; Rony Amaya, Amir Akbari, Mohammed Labadlia, Department of Electronics, Carleton University, Canada; Bhavana Deore, Chantal Paquet, Nicolas Milliken, Tabitha Arulpragasam, Security and Disruptive Technologies National Research Council Canada, Canada
Coffee Break
Tue, 15 Jul, 10:00 - 10:20

TU-A6.2A.6: Ti3C2Tx MXene Coated Polylactic Acid Horn Antenna for Ku Frequency Band Communications
Zahra Sarpanah Sourkouhi, university of British Columbia, Canada; Jamal Alhourani, Yury Gogotsi, Drexel University, United States; Mohammad H. Zarifi, university of British Columbia, Canada
Virtual Presentation
Tue, 15 Jul, 10:20 - 10:40

TU-A6.2A.7: A 12-port MIMO Wide-Band Multi-Band 3D Printed ITS Antenna for Laptop Applications
Jayshri Kulkarni, Jack H Engdahl, Wentworth Institute of Technology, United States; Karthik Kakaraparty, Florida Polytechnic University, United States; Douglas Dow, Wentworth Institute of Technology, United States; Yang Li, Baylor University, United States
Tue, 15 Jul, 10:40 - 11:00

TU-A6.2A.8: On The Design of Flexible Phased Array Antenna Using 3D-Printable Conductive and Non-Conductive Filaments for Conformal Applications
Luke Rosen, Valliammai Arunachalam, Dipankar Mitra, University of Wisconsin-La Crosse, United States
Tue, 15 Jul, 11:00 - 11:20

TU-A6.2A.9: An Ultra Lightweight 3D-Printed Ku-band Pyramidal Horn Antenna for Satellite Communication Equipment
Burak Demirbuken, Mustafa Berkay Ilkar, Hacettepe University, Turkey; Adnan Iftikhar, Muhammad Farhan Shafique, COMSATS University Islamabad, Turkey; Noman Naseer, Queen Mary University London, United Kingdom; Birsen Saka, Hacettepe University, Turkey; Muhammad Qamar, Queen Mary University London, United Kingdom
Tue, 15 Jul, 11:20 - 11:40

TU-A6.2A.10: Low Loss 3D Printed Feed Networks for 5G Cellular Applications
Nicholas Sanford, Washington University in St. Louis, United States; Nichole Miller, Ravi Challa, Ian Winfield, FABRIC8LABS, United States; John Sanford, University of California, San Diego, United States